Plumbing 101: What You Must Have for Installing a Bathtub
Plumbing 101: What You Must Have for Installing a Bathtub
Blog Article
We've uncovered this post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the internet and thought it made perfect sense to talk about it with you over here.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Setting up a bathtub isn't specifically rocket science, yet it does require strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately challenging task. If the old tub is readily available, the job can move speedily; if you need to open a wall to eliminate the old bathtub as well as place the new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub and also set in the brand-new one. See to it you have actually certified yourself for the job as well as are comfortable attempting it. As opposed to employing a professional to take control of a halfway-completed task, it is far better to consider employing one before you start. Possibilities are you may need a professional plumber to make tube links.
This post will certainly help you install a new bath tub in your restroom if you have currently acquired a brand-new bathtub as well as do not need to alter the arrangement of your previous supply of water pipelines.
Your devices and also product checklist ought to comprise the following:
Preparing for the Installment
First of all, the supporting frame supplied with the bath needs to be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be suited its last position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, after that the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The process of removing the existing taps can be rather troublesome because of the restricted gain access to that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipelines. Once the supply pipes have been gotten rid of, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Tub
Using the two wood boards under its feet, put the bathtub in the called for position. The wood boards are useful in evenly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small points.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level as well as adjusting the feet on the tub up until the spirit level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap port to the ideal supply pipeline by making a compression join; after that do the exact same for the other tap.
Turn on the water system and examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Load the bathtub as well as also examine the overflow outlet and also the normal outlet for leaks.
Lastly, fix the bathroom paneling as defined in the producer's user's manual. Tiling and also sealing around the bathtub must wait till the tub has actually been made use of at least once as this will settle it into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines are in area in between the tap and also the sink. Protect the faucet in position with the producer provided backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type must be linked to the tap finishes initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture an inflexible seal, creating the water to pass through the wall in between the bathroom and also the tiling, bring about issues with moisture as well as possible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly load the tub with water before securing, to permit the movement experienced when the bathtub remains in usage. The sealant can break fairly very early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly readily available on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed reading our excerpt about A Step-by-Step Guide to Installing a Bathtub. Thank you so much for finding the time to read through our content. Sharing is caring. You never know, you may just be helping someone out. Many thanks for your time spent reading it.
Address emergency plumbing promptly here. Report this page